Tutorial.TiltSensor History

Show minor edits - Show changes to markup

June 12, 2007, at 03:53 PM by David A. Mellis -
Changed line 17 from:

Use the 'Digital > Button example to read the tilt-sensor, but you'll need to make sure that the inputPin variable in the code matches the digital pin you're using on the Arduino board.

to:

Use the Digital > Button example to read the tilt-sensor, but you'll need to make sure that the inputPin variable in the code matches the digital pin you're using on the Arduino board.

June 12, 2007, at 03:53 PM by David A. Mellis -
Added lines 9-10:

Circuit

Changed lines 15-44 from:
 
/* Tilt Sensor
 * -----------
 *
 * Detects if the sensor has been tilted or not and
 * lights up the LED if so. Note that due to the
 * use of active low inputs (through a pull-up resistor)
 * the input is at low when the sensor is active.
 *
 * (cleft) David Cuartielles for DojoCorp and K3
 * @author: D. Cuartielles
 *
 */

int ledPin = 13;
int inPin = 7; 
int value = 0;

void setup() 
{
  pinMode(ledPin, OUTPUT);              // initializes digital pin 13 as output
  pinMode(inPin, INPUT);                // initializes digital pin 7 as input
}

void loop() 
{
  value = digitalRead(inPin);   // reads the value at a digital input 
  digitalWrite(ledPin, value);           
}

to:

Code

Use the 'Digital > Button example to read the tilt-sensor, but you'll need to make sure that the inputPin variable in the code matches the digital pin you're using on the Arduino board.

December 01, 2006, at 11:57 AM by David Cuartielles -
Changed lines 7-8 from:

The prototyping board has been populated with a 1K resitor to make the pull-up and the sensor itself. We have chosen the tilt sensor from Assemtech, which datasheet can be found here. The hardware was mounted and photographed by Anders Gran, the software comes from the basic Arduino examples.

to:

The prototyping board has been populated with a 1K resitor to make the pull-up and the sensor itself. We have chosen the tilt sensor from Assemtech, which datasheet can be found here. The hardware was mounted and photographed by Anders Gran, the software comes from the basic Arduino examples.

Changed lines 11-12 from:

Picture of a protoboard supporting the tilt sensor, by Anders Gran

to:

Picture of a protoboard supporting the tilt sensor, by Anders Gran

January 04, 2006, at 01:27 PM by 193.222.246.39 -
Added lines 1-42:

Tilt Sensor

The tilt sensor is a component that can detect the tilting of an object. However it is only the equivalent to a pushbutton activated through a different physical mechanism. This type of sensor is the environmental-friendly version of a mercury-switch. It contains a metallic ball inside that will commute the two pins of the device from on to off and viceversa if the sensor reaches a certain angle.

The code example is exactly as the one we would use for a pushbutton but substituting this one with the tilt sensor. We use a pull-up resistor (thus use active-low to activate the pins) and connect the sensor to a digital input pin that we will read when needed.

The prototyping board has been populated with a 1K resitor to make the pull-up and the sensor itself. We have chosen the tilt sensor from Assemtech, which datasheet can be found here. The hardware was mounted and photographed by Anders Gran, the software comes from the basic Arduino examples.

http://static.flickr.com/30/65458903_d9a89442a9.jpg

Picture of a protoboard supporting the tilt sensor, by Anders Gran

 
/* Tilt Sensor
 * -----------
 *
 * Detects if the sensor has been tilted or not and
 * lights up the LED if so. Note that due to the
 * use of active low inputs (through a pull-up resistor)
 * the input is at low when the sensor is active.
 *
 * (cleft) David Cuartielles for DojoCorp and K3
 * @author: D. Cuartielles
 *
 */

int ledPin = 13;
int inPin = 7; 
int value = 0;

void setup() 
{
  pinMode(ledPin, OUTPUT);              // initializes digital pin 13 as output
  pinMode(inPin, INPUT);                // initializes digital pin 7 as input
}

void loop() 
{
  value = digitalRead(inPin);   // reads the value at a digital input 
  digitalWrite(ledPin, value);           
}

Share