This page is also available in 3 other languages
Change language 
Polskie

Treść dokumentacji Arduino jest na licencji Licencji Creative Commons Attribution-Share Alike 3.0.

Szukasz czegoś co można ulepszyć? Zaproponuj poprawki i nową dokumentację za pomocą GitHub.

Wątpliwości, jak używać Github? Dowiedz się wszystkiego, co musisz wiedzieć w tym samouczku.

Last Revision: Searching...

Last Build: 2024/11/08

Redaguj tą stronę
Reference > Language > Functions > Analog io > Analogreference

analogReference()

[Analogowe We/wy]

Description

Configures the reference voltage used for analog input (i.e. the value used as the top of the input range). The options are:

Arduino AVR Boards (Uno, Mega, etc.)

  • DEFAULT: the default analog reference of 5 volts (on 5V Arduino boards) or 3.3 volts (on 3.3V Arduino boards)

  • INTERNAL: an built-in reference, equal to 1.1 volts on the ATmega168 or ATmega328P and 2.56 volts on the ATmega8 (not available on the Arduino Mega)

  • INTERNAL1V1: a built-in 1.1V reference (Arduino Mega only)

  • INTERNAL2V56: a built-in 2.56V reference (Arduino Mega only)

  • EXTERNAL: the voltage applied to the AREF pin (0 to 5V only) is used as the reference.

Arduino SAMD Boards (Zero, etc.)

  • AR_DEFAULT: the default analog reference of 3.3V

  • AR_INTERNAL: a built-in 2.23V reference

  • AR_INTERNAL1V0: a built-in 1.0V reference

  • AR_INTERNAL1V65: a built-in 1.65V reference

  • AR_INTERNAL2V23: a built-in 2.23V reference

  • AR_EXTERNAL: the voltage applied to the AREF pin is used as the reference

Arduino megaAVR Boards (Uno WiFi Rev2)

  • DEFAULT: a built-in 0.55V reference

  • INTERNAL: a built-in 0.55V reference

  • VDD: Vdd of the ATmega4809. 5V on the Uno WiFi Rev2

  • INTERNAL0V55: a built-in 0.55V reference

  • INTERNAL1V1: a built-in 1.1V reference

  • INTERNAL1V5: a built-in 1.5V reference

  • INTERNAL2V5: a built-in 2.5V reference

  • INTERNAL4V3: a built-in 4.3V reference

  • EXTERNAL: the voltage applied to the AREF pin (0 to 5V only) is used as the reference

Arduino SAM Boards (Due)

  • AR_DEFAULT: the default analog reference of 3.3V. This is the only supported option for the Due.

Syntax

analogReference(type)

Parameters

type: which type of reference to use (see list of options in the description).

Returns

Nothing

Notes and Warnings

After changing the analog reference, the first few readings from analogRead() may not be accurate.

Don’t use anything less than 0V or more than 5V for external reference voltage on the AREF pin! If you’re using an external reference on the AREF pin, you must set the analog reference to EXTERNAL before calling analogRead(). Otherwise, you will short together the active reference voltage (internally generated) and the AREF pin, possibly damaging the microcontroller on your Arduino board.

Alternatively, you can connect the external reference voltage to the AREF pin through a 5K resistor, allowing you to switch between external and internal reference voltages. Note that the resistor will alter the voltage that gets used as the reference because there is an internal 32K resistor on the AREF pin. The two act as a voltage divider, so, for example, 2.5V applied through the resistor will yield 2.5 * 32 / (32 + 5) = ~2.2V at the AREF pin.