This page is also available in 3 other languages
Change language 
Polskie

Treść dokumentacji Arduino jest na licencji Licencji Creative Commons Attribution-Share Alike 3.0.

Szukasz czegoś co można ulepszyć? Zaproponuj poprawki i nową dokumentację za pomocą GitHub.

Wątpliwości, jak używać Github? Dowiedz się wszystkiego, co musisz wiedzieć w tym samouczku.

Last Revision: Searching...

Last Build: 2024/11/08

Redaguj tą stronę
Reference > Language > Functions > Analog io > Analogwrite

analogWrite()

[Analogowe We/Wy]

Description

Writes an analog value (PWM wave) to a pin. Can be used to light a LED at varying brightnesses or drive a motor at various speeds. After a call to analogWrite(), the pin will generate a steady square wave of the specified duty cycle until the next call to analogWrite() (or a call to digitalRead() or digitalWrite()) on the same pin.

Board PWM Pins PWM Frequency

Uno, Nano, Mini

3, 5, 6, 9, 10, 11

490 Hz (pins 5 and 6: 980 Hz)

Mega

2 - 13, 44 - 46

490 Hz (pins 4 and 13: 980 Hz)

Leonardo, Micro, Yún

3, 5, 6, 9, 10, 11, 13

490 Hz (pins 3 and 11: 980 Hz)

Uno WiFi Rev.2

3, 5, 6, 9, 10

976 Hz

MKR boards *

0 - 8, 10, A3 (18), A4 (19)

732 Hz

MKR1000 WiFi *

0 - 8, 10, 11, A3 (18), A4 (19)

732 Hz

Zero *

3 - 13, A0 (14), A1 (15)

732 Hz

Due **

2-13

1000 Hz

101

3, 5, 6, 9

pins 3 and 9: 490 Hz, pins 5 and 6: 980 Hz

* In addition to PWM capabilities on the pins noted above, the MKR and Zero boards have true analog output when using analogWrite() on the DAC0 (A0) pin.
** In addition to PWM capabilities on the pins noted above, the Due has true analog output when using analogWrite() on pins DAC0 and DAC1.

You do not need to call pinMode() to set the pin as an output before calling analogWrite().
The analogWrite function has nothing to do with the analog pins or the analogRead function.

Syntax

analogWrite(pin, value)

Parameters

pin: the Arduino pin to write to. Allowed data types: int.
value: the duty cycle: between 0 (always off) and 255 (always on). Allowed data types: int.

Returns

Nothing

Example Code

Sets the output to the LED proportional to the value read from the potentiometer.

int ledPin = 9;      // LED connected to digital pin 9
int analogPin = 3;   // potentiometer connected to analog pin 3
int val = 0;         // variable to store the read value

void setup() {
  pinMode(ledPin, OUTPUT);  // sets the pin as output
}

void loop() {
  val = analogRead(analogPin);  // read the input pin
  analogWrite(ledPin, val / 4); // analogRead values go from 0 to 1023, analogWrite values from 0 to 255
}

Notes and Warnings

The PWM outputs generated on pins 5 and 6 will have higher-than-expected duty cycles. This is because of interactions with the millis() and delay() functions, which share the same internal timer used to generate those PWM outputs. This will be noticed mostly on low duty-cycle settings (e.g. 0 - 10) and may result in a value of 0 not fully turning off the output on pins 5 and 6.

See also

  • DEFINITION PWM